DIY ’100 Hour Candles’

DIY 100 hr candles

  • Liquid Paraffin (Lantern Oil)
  • Wicks
  • 1/2 Pint Mason Jars

I am always on the look-out for homemade counterparts to store bought preparations. These DIY ’100 hour candles’ definitely fit the bill. In less than 5 minutes you have an inexpensive, refillable ’100 hour candle’ that will light up your home in the darkest of times. And for you ladies – these homemade alternatives are far more aesthetically pleasing than the store bought versions. So let’s get started.

Supplies

The supplies you need are pretty straight forward. Liquid paraffin, lantern wicks and 1/2 pint mason jars. I found my lantern wicks and mason jars at Walmart and the liquid paraffin at a local Hobby Lobby. The cost of each candle ends up being approximately $2.70 per candle. Which is about half the cost (at least) of the store bought versions.

Just as a side note, it took me forever to find the liquid paraffin. Make sure when you’re calling around that you ask for liquid paraffin and not the paraffin wax. The paraffin wax is just a wax block that will melt then solidify when it cools. If you can’t seem to locate liquid paraffin you can replace it with mineral oil and coconut oil with a ratio of 2:1.

 

Step One: Create Opening For Wick

I used some grass-trimming shears but you can use a knife or any other sharp tool to create your opening. Just make it wide enough to fit in the wick SNUGLY.

 

Step Two: Insert Wick

Instead of just putting the wick in like a candle, we’re going to place it so that it is doubled over. First, pull the wick through the canning top so the end is sticking out on the side that will face inside of the mason jar. Next you’re going to use your knife (or shears for me) to push the second end through as well. This should make the wick fit in pretty tight.

After having both ends through, pull down so that only a tiny amount of the folded piece of wick remains.

 

 

 

 

 

Step Three: Pour Paraffin Into Jar

Fill up your 1/2 pint mason jar with the liquid paraffin.

Step Four: Secure the Top

Separate the two ends of the wick so they are at a v-shape when they are put into the jar. This just helps the wick soak up the oil from both sides when it’s getting low. Place the top on the jar and screw the band on around it.

 

To Prevent Evaporation

The paraffin will evaporate if the wick is left exposed to the air. This is why the store bought versions will have a plastic cap with each candle. To prevent this from happening, simply get an extra canning lid and put it on top in between the wick and the band.

 

 

Comparing to the Store Bought Version

 

The benefits of making your own DIY emergency candles are substantial. First, they are cheaper. The least expensive place I found the store-bought versions were around $5.00. As I mentioned before, the homemade version comes out to about $2.70 each.

Second, they put out more light. As you can see in the picture above, the flame is significantly larger. This could end up being a liability for you. It is obviously more dangerous, but proper candle safety should prevent any injury.

Third, they are refillable. The store bought versions are made for a one-time use only.

Fourth, they are made out of glass. Once again, this is more of a personal preference but my experience with the plastic store bought versions is that they very easily squirt lantern oil from the top if you hold them too tight. The light plastic also makes me nervous that they will tip. The durable and heavy glass of the mason jars eliminates the possibility of squirting flammable material all over your house and it is definitely more stable to prevent tipping.

Read more: http://saltnprepper.com/diy-100-hour-candles/#ixzz2I3cP3iRM

Related Posts Plugin for WordPress, Blogger...

4 thoughts on “DIY ’100 Hour Candles’

  1. im having a hard time with the wick process do you have a YouTube video of this? I am a visual person lol

  2. Are you saying to fold the wick in half so both ends are sticking out the top?

Comments are closed.